|
|
Catalogue > Indicators
Here is our current range of Indicators. You will need adobe acrobat reader to view the products with *.pdf files in more detail. |
| 9820.pdf |
 |
Model 9820 digital indicator
True Bipolar operation +/- 50mV input
5 digit (+/-99,999) LED display
Non-linearity <+/- 0.01%
Analogue output +/- 10Vdc (2kHz)
Front panel Shunt calibration
Peak & Valley monitoring
Remote & Front panel Tare
Power for four 350 ohm load cells
Full CE compliance |
| 9840.pdf |
 |
Model 9840 calibration grade digital indicator
Ultra-high accuracy digital indicator
True Bipolar operation +/- 4.5 mV/V input
Internal resolution 24 bits, +/- 999,999 display counts
Non-linearity <+/-0.01%
Auto set-up for 25 load cells
Peak/Valley hold with front panel reset
Remote & Front panel Tare
Full duplex RS-232 (optional RS-485)communication
Front panel ShuntCal with 2 selectable resistors
Multi-point linearised calibration
Display unit conversion: lb, kg, N, Psi, Mpa, klb, kN, t.
Vacuum fluorescent display
Full CE compliance
Optional totally independent second channel |
| dfi01.pdf |
 |
Model DFI-01 Calibration grade indicator
Ultra-high accuracy calibration grade indicator
Internal resolution 1:1,000,000 using 20 bit ADC
Display resolution 1:300,000 with +/-999,999 display
Bipolar ratiometric input to +/- 4.5mV/V
Integral non-linearity 0.0007%, differential +/-0.5LSB
Sensitivity to 0.1 µVolt
Peak capture facility
Full duplex RS-232/485 communication
Independent RS-232 printer port
CE 97 compliance
Options; Display hold, UKAS calibration, Analogue output & AS600 calibrator |
| dfi05.pdf |
 |
Model DFI-05L High accuracy indicator
Internal resolution 1:63,000 using 16 bit ADC
Display resolution 1:60,000
+999,999/-199,999 display counts
Bipolar ratiometric input to +/- 4mV/V
Sensitivity to less than 1 µVolt
Multi-point linearised calibration
Max/Min values stored
CE 97 compliance
Optional. RS-232 output, 2 or 4 relay outputs
|
| n/a |
 |
Model AD21MV
Digital indicator
Maximum input +/- 25mV, sensitivity 1 µVolt
4 digit -1999 to 9999 LED display
Accuracy 0.1% +/- 1 digit
Transducer excitation 10 Vdc
Connection by screw terminal connectors
Scaling by links behind front panel
CE approval
Power supply choice 240 Vac, 115 Vac or 12 Vdc |
| n/a |
 |
Model AD33 digital indicator
Low cost 5 digit indicator
Maximum input +/- 100mV, sensitivity 1.52 µVolt
240 Vac power
Connections via screwdriver terminals
Programmable 0-12 Vdc excitation @ 35mA
1/8 DIN panel mounting
Universal power input 90-260 Vac
RS-422/485 communications
CE approved |
| n/a |
 |
Model SY025S
5 digit 7 segment red LED display indicator
Internal resolution 24 bit binary (1:16.7M)
Sensitivity 1.2uV @ 2mV/V; 0.8uV @ 1.5mV/V
Programming & Output via RS-232/485 link
Excitation 10 Vdc @ up to 120mA
Peak Hold or Continuous modes
Remote Tare & Reset from rear panel
Panel mount Noryl case 1/8 DIN
Connections via screw terminal connectors
Options: Programmer module, Relay outputs, Dump to printer, Case/Wallmount
Model SY025HR
High resolution digital indicator
Sensitivity to less than 1 µVolt
Extra digit +999,999/-99,999 display |
| sy021.pdf |
 |
Model SY021 Battery powered handheld Load Meter
Accurate 4/5 digit indicator
LCD 2 line 16 character display
Internal 6V 4x AA alkaline batteries
4-pin locking DIN connector
Up to 50 calibrations per channel
Easy re-calibration for new sensors
Selectable engineering units; lb, kg, N & t
Tare & Reset buttons
Peak Hold or Continuous readout
Opt. 2nd input channel and Backlit display |
|
© 1999-2004 Interface Force Measurements Ltd
Initial design by www.si4.net
|
